recycling crafts – Page 2 – Our Beautifully Messy House

Pumpkin Jar Craft

October 2, 2015October 2, 2015 Porter 6 Comments

I am so excited that October is finally here and we can start doing some Halloween crafts around our house! This PUMPKIN JAR CRAFT was inspired by the Jam Jar Fairy Houses we made last Spring. It’s a very similar concept! While many people think hot glue guns are just for gluing things together, we like to use them to add texture to our crafts as well. The hot glue gives our pumpkin jars a true, warty pumpkin appearance! I love the way they look with and without jack-o-lantern faces, in the day and at night! Too cute!!!

Materials needed:

jars, various sizes
hot glue gun and glue
acrylic paint
green, glitter spray paint
battery-operated tea lights

First, decide whether or not you’d like jack-o-lantern faces on your jars. I really liked our mixed…two with, one without. If you’re putting a face on your jar, carefully do that first with the hot glue gun. One great thing about hot glue gun glue: if you make a mistake, simply let the glue cool completely, then peel it off and start again!

Next, fill in the spaces and go around the jar with long, vertical stripes of hot glue. It certainly doesn’t need to be perfect…no two pumpkins are ever alike!

After the glue has cooled completely, paint the inside of the jar yellow, where the face shines through.

Now, paint the exterior of the jar orange. We painted ours with a mix of yellow and orange to give the pumpkins varying hues. Be careful around the face!

The pumpkins without jack-o-lantern faces are perfect for your littles to paint!

As the jars dry, spray your lids with glittery, green spray paint. Do this outside or in a well-ventilated area. If you don’t have spray paint, green acrylics would work fine too!

After the lids have dried, screw them on top your jars and your pumpkin jars are complete! Now for the fun part…find a place to display your pumpkins for everyone to enjoy! At nighttime, place a battery-operated tea light inside each jar to bring your pumpkins to life!

Are they cute or what? Enjoy!!!

DIY Jacob’s Ladder Toy

September 29, 2015October 2, 2015 Porter Leave a comment

I really wanted to make L a Jacob’s Ladder Toy, but didn’t want to make a trip to the local hardware or craft store for supplies. So, we made this Jacob’s Ladder out of an old board book! (If you don’t have a board book they are easy to find at the dollar store.) I just love the outcome! This one is super-colorful compared to the wooden one I had as a kid and is just as much fun!

I loved playing with my Jacob’s Ladder when I was young…it’s such a unique toy! Flip-flopping it back and forth is very calming, but it also makes you think creatively and problem solve. I enjoyed watching L play with the one we made today…not only was she ecstatic when she finally figured out how to work a Jacob’s Ladder, but she was also folding it into shapes, pretending it was a snake, a bracelet and a funky hat.

Materials needed:

board book
3 pieces of ribbon (35 inches long each)
glue
box cutter
paper cutter (optional)
scissors

First, using a box cutter, disassemble your board book.

Next, measure the dimensions of one page and decide how best to cut it. The book I used was 7 in x 7 in. I chose to cut the pages down the middle in one direction and into thirds going the other direction. Each piece ended up being 3.5 in x 2.25 in. If you have a paper cutter on hand, it makes this step super quick and easy! I cut up 4 pages, leaving me with 24 pieces.

Once you have 24 pieces cut, sort them into “nice” and “ugly” piles, 12 cards in each pile. The “ugly” cards won’t be seen.

Next, glue each “nice” card to an “ugly” card with a thin layer of wood glue. Put some canned food on top of the cards to keep them flat and clamped down for the first few minutes, while the glue is setting. Once they are all glued, let them dry for an hour or two. You should now have 12, double-stacked cards.

Now, time to make that Jacob’s Ladder! Lay one card-stack in front of you, “nice” side down. Spread a thin layer of glue on top of the card-stack. Place the ends of all three strips of ribbon onto the card-stack. As you can see in the photos, two of the ribbons spread out into one direction and the other ribbon to the opposite direction.

Spread a dab of glue on each ribbon end and press another card-stack carefully on top, “nice” side up.

Fold all the ribbons over the top of the cards and to the opposite direction. Pulling them taut, place another card-stack on top of the ribbons, “nice” side down.

Spread a thin layer of glue on the card-stack and fold the ribbons over, keeping them pulled taut much as possible. You can press the ribbons down into the glue to hold them in place.

Spread a dab of glue on top of the ribbons, and press another card-stack on top, “nice” side up.

Folding the ribbons over again, repeat the last three steps, until you reach the last card-stack and the end of your ribbon.

Trim the ribbon, pull it taut, and glue it in between the last two card-stacks.

Place a can of food on top of the entire Jacob’s Ladder Toy and allow the glue to dry completely for an hour or two.

Now, time to play!!! If you’ve never used a Jacob’s Ladder before, you flip the top card to one side and let gravity do the rest of the work. The card’s flip-flop down, one after another, like magic in your own hands!

Enjoy!!!

DIY Toy Sail Boat

September 3, 2015October 22, 2015 Porter Leave a comment

One evening this summer, while we were getting ready for bath time, L pulled a wine cork out of her pocket. She had been saving it all day to float it around and play with in the bath tub. That got me thinking…I knew with a few toothpicks and some leaves we could turn her wine cork into a little sail boat! Leaves work great for this project, because they’re naturally water-proof and easily replaceable!

Materials needed:

2 wine corks
4 toothpicks
2 leaves
old pencil
scissors

Take one of the wine corks and stick three toothpicks into it, all pointing in the same direction in a line.

Next, push the second wine cork into the opposite ends of the toothpicks.

Stick one more toothpick vertically into the middle of one of the corks.

Find a medium-sized leaf and weave it through the bottom toothpicks. We used a balloon flower leaf. This step isn’t necessary, but it makes a nice lil bed for anything you may want to sail on top…a bug, a rock, a fairy friend.

Next, find a slightly larger leaf and thread it onto the vertical toothpick, making a sail. We found the hosta leaves to work best for this, though any thick and sturdy leaf will do!

To make the sail boat safer for little hands, twist an eraser off the top of an old pencil. Cut it in half with scissors and push it onto the top of the sail.

Now, time to play! L had hours of fun blowing her boats around our rain barrel!

The boats may not seem like much, but ours withstood some submarine plunges under the water and lasted through two nights of bath time play! Tomorrow, we’ll replace the leaves and keep sailing!

Enjoy!!!

Coffee Can Stilts

August 27, 2015October 22, 2015 Porter Leave a comment

A few weeks ago a family friend called me up to ask if I had a use for a bunch of old coffee cans. While I was a little afraid to tell my husband that I had said “yes” to accepting such a large bag of junk, taking up more room in our house, I was over-the-moon excited to be acquiring these cans! I knew just what we’d use them for…COFFEE CAN STILTS!!! These are so quick and easy to make and are so much fun for the kids! Walking on stilts is all L wants to do these days!!! “I can almost touch the sky from up here, Mom!”

Materials needed:

2 coffee cans
church key can opener
rope
scissors
paint (optional)
acrylic sealant (optional)

First, if you want your stilts to be colorful, have your little ones paint the cans with acrylic paints. After the paint has dried, spray on a coat of acrylic sealant to give the cans a glossy finish.

Next, using a church key can opener, make two holes on the bottoms of the cans. The holes should be opposite each other. Try to bend the metal all the way back inside the can, so no sharp points protrude out. (Your kids shouldn’t have their hands inside the cans at anytime, but you never know when the curious ones may take off the lid while playing and reach inside…so, better safe than sorry!)

Cut two pieces of rope. To find the correct length, have your kid stand on the rope, holding both ends in his or her hands pulled up to chest-level. This is a good place to cut it. After the stilts are assembled, the rope handles should reach your child’s waist.

Thread the rope into the holes of the can from the outside. Once both ends are pulled through, tie a knot in each end. Repeat on the second can.

Place the lids back onto the cans and flip them over. Having the lids isn’t a necessity, but it may save your floors from being scratched up while your children walk around inside. Now, time to play!!!

As your little ones practice, they’ll get better and better at walking on their stilts and they’ll be oh-so-proud!!! Future circus performers, anyone?

Talk about good hand-eye-FOOT coordination! Enjoy!!!

DIY Toy Catapult

July 16, 2015September 24, 2015 Porter Leave a comment

What kid (or adult) doesn’t love launching things through the air? This DIY TOY CATAPULT takes only minutes to put together and your kids will play with it for hours…days even! I love how kids naturally experiment while playing with this toy. Even as young as three, L was moving the can (the fulcrum) around, placing the balls in various slots, and went on to launch her toy parachute, as well as her shoes! So much fun!!!

Materials needed:

yard stick
can of food
egg carton
scissors
hot glue gun
permanent markers (optional)

Things to launch:

ping pong balls
pom poms
-cotton balls
DIY Pocket Parachute
plastic figurines (fairies, dinosaurs, army men)
marshmallows or cereal (to catch in one’s mouth)

First, cut your egg carton in half.

Using a hot glue gun, glue the egg carton onto one end of your yard stick. (Don’t worry…when your kids are done playing with their catapult, the egg carton and glue should peel right off the yard stick! I take ours apart every time we’re finished playing with it!)

Next, number your egg carton slots and your ping pong balls. This step is optional, but it makes it easy to keep track of what ball goes the farthest and which slots you’re putting things into…especially if you’re launching multiple balls at once!

The set-up of your catapult is easy…just place the can on it’s side in the grass (keeps it from rolling) and place the yardstick on top. Fill the slots with your projectiles!

Now, time to play!!!

Launching balls…

Parachutes…

And L’s shoes…

What will you all send flying through the air???

If your kids like the catapult, they’ll definitely love making POCKET PARACHUTES…another “make something from nothing” craft! Enjoy!

DIY Pocket Parachute

June 10, 2015September 24, 2015 Porter Leave a comment

What kid doesn’t love throwing a toy parachute around?!! And what parent doesn’t love a toy that costs nothing, takes less than 5 minutes to make, and entertains your kids for hours on end?!! I made this DIY POCKET PARACHUTE for L on a rainy day last week…as soon as there was a break in the weather, we were out the door throwing the parachute all around town. L dropped the parachute off the steps of the old courthouse, a church, the library, a little pavilion stage, and she climbed up a tree and dropped it down as well. This pocket parachute is so simple, so easy, and so much fun!!!

Materials needed:

plastic bag
food pouch cap
string
scissors
an awl (or screwdriver)

If you don’t have a food pouch cap, a toy wheel, some safety pins, paper clips or a wine cork could be used as well…get creative with what you have on hand!

First, cut the plastic bag into a square at least 12×12 inches.

Cut your string into 4 equal pieces, all approximately 15 inches long.

Using the awl, carefully poke a hole through the center of the food pouch cap.

Also, poke holes into each corner of the square you cut from the plastic bag. Make each hole 1/2 an inch from the edges.

Tie a piece of string onto each corner, using a double knot.

Next, gather all the strings together and tie them together with one overhand knot, about 3 inches from the end.

Thread two of the strings through the center of the food pouch cap and thread the other two through the side. Tie the ends together with a double knot.

Too easy, right? Now time to play!!! It’s just as much fun trying to catch the parachute as it is to throw it!

If your kids are older, they can experiment by making various parachutes…some out of bigger pieces of plastic, longer strings and cutting a hole in the center parachute as well. Enjoy!!!

DIY String Bowls

April 6, 2015September 25, 2015 Porter Leave a comment

Before we packed up our Easter stuff, I decided to make some fun and funky STRING BOWLS with L…we used the bottoms of our Easter eggs for molds. How cute are these? And even better, all the materials needed we already had lying around the house…you probably do too! If you don’t have Easter egg bottoms to use, any small or medium-sized bowls will work for molds.

Materials needed:

small plastic bowls or Easter egg bottoms
yarn or string
white glue
water
plastic wrap
scissors
glitter (optional)
hair dryer (optional)

First, cover your molds with plastic wrap.

In a small bowl, mix a little bit of water into some white glue. If you like, mix some glitter into the glue as well.

Next, cut your string into small pieces and stir it into the glue. You can experiment with this step…we did one bowl using 1-inch pieces of yarn, another using 2-3 inch pieces, and one bowl using one long piece of string.

Remove each piece of string from the glue, one at a time, and lay them across your mold. If the glue is thick on the string, you can squeeze some of the excess glue off.

Once all your string is laid out across and around your molds, lay them aside to dry. It may take a couple days for the glue to dry completely, or you can speed up the process by using a hair dryer.

After the glue has dried, turn your bowls over. Remove the molds and the plastic wrap.

Using fine-tipped scissors, you can trim any string or glue that you may need to off the edges.

Beautiful and fun! Perfect for rings, hair clips, buttons and trinkets!

DIY Tin Can Bird Feeder #2

February 26, 2015December 3, 2015 Porter Leave a comment

To celebrate the last week of National Bird Feeding Month, L and I made these adorable TIN CAN BIRD FEEDERS! They are really easy to make, look beautiful and cost nothing…just go digging through your recyclables! Not only will the birds love this winter treat, this bird feeder would make a fantastic gift for your children to make for a friend, parent or grandparent!

Materials needed:

tin can w/ lid
wooden paint stirrer
pliers
acrylic paints
hot glue gun
string
glossy sealant (optional)
church key can and bottle opener (optional)
bird seed

First, make sure your can is clean and remove the label.

Using your hands, carefully bend the lid of the can in half. Using pliers, squeeze it flat.

Using the hot glue gun, glue the paint stirrer inside the can. You can break the stirrer if it’s too long. This will be the birds’ perch.

Next, glue the bent lid back into the can as pictured. Try not to make a huge mess with the hot glue gun, but if the glue shows it is no big deal…you will paint over it next.

Paint the can any way you like.

After the paint dries, you can use the can opener to make holes in the can from where you’ll hang it on a string. On one of our cans I placed two holes on the top…this bird feeder will hang from an old clothes line end.

On our second can I made holes in the back of the bird feeder…this one we will tie onto a fence. I was careful to put the holes in the can after we painted it, because I wanted to avoid any sharp edges while L was handling the bird feeder.

If you’d like your bird feeder to have a shiny, glossy finish, spray the can with a glossy sealant. It only takes 15-30 min to dry and will help protect the paint as well!

Thread string through the holes of the bird feeder and fill with bird seed!

Now, find the perfect spot to hang your TIN CAN BIRD FEEDER! We placed one of ours right outside our kitchen window…the girls will love watching their little wildlife friends snack throughout the day! Enjoy!

In case you missed it, here’s the first DIY TIN CAN BIRD FEEDER we made! Another fun nature craft!

DIY Toy Vacuum (that Really Cleans!!!)

February 25, 2015September 26, 2015 Porter Leave a comment

I love showing my kids that with a little creativity and a basketful of recycling materials you can make just about anything! One morning L woke up asking me to make her a vacuum…strange request, but I accepted the challenge. My thoughts immediately went to that toy vacuum from yesteryear with the popping balls inside. Kids love those things because of the noise they make, so I knew ours had to be similar. The only thing to improve upon that vacuum would be to make one that cleans as well! So here you have it — a toy vacuum that essentially costs you nothing (assuming you have all the materials) and it actually cleans the floors while your kid plays!

Materials needeed:

Swiffer sweeper w/ dry swiffer pad
empty milk carton
plastic container (like one berries come in)
plastic beads
duct tape
paper towel tube (optional)
hot glue gun
scissors

First, using scissors or a knife, cut a little window on the front of the milk carton. Cut a piece of clear plastic off of the plastic container to cover the window.

Using a hot glue gun, carefully glue the clear plastic in place over the “window.”

Cover the entire milk carton in duct tape. Make sure you cover up the glued edges of the plastic window as well…this should eliminate any sharp or pointy edges.

Next, have your little one help you drop beads into the carton. A few handfuls will do. Screw the lid back on the carton.

If your Swiffer sweeper’s handle has removable links (which I think they all do), remove the two middle ones to make it a more suitable height for your child.

Now the next step you can do in two ways: you can tape the milk carton directly onto the Swiffer sweeper…it may be more secure, but it may also leave some duct tape residue on the Swiffer. (That would be the more permanent option.) Or, you can glue and tape a paper towel tube onto the back of the milk carton and slide it onto the Swiffer’s handle. We went with the later…I thought it may jiggle more and make a louder, bead-popping sound too!

Now to clean floors…just replace the Swiffer pad as you would normally do and let your child go to work! (I mean play!) I really thought ours would last a couple weeks, but we’re going on 4 months now and every week L asks if she can help “vacuum” the floors. Enjoy!!!

DIY Floppy Newspaper Hats

November 6, 2014November 3, 2015 Porter Leave a comment

Oh, we had so much fun making these FLOPPY NEWSPAPER HATS today! I thought I’d write up this tutorial this weekend, but I just couldn’t wait…they’re just so much fun! If you have little boys in your messy house, please don’t think you can’t make these with them…a hat’s a hat! A floppy hat’s a floppy hat! I’m sure they’ll love them just as much as any girls will! Do it! There will be lots of giggling for sure.

Materials needed:

newspaper
acrylic paint
painters tape
tissue paper, poof balls, feathers, etc.
white glue

First, prepare your painting area. I taped some trash bags to the floor to protect it from paint…not usually necessary for painting, but the newspaper sheets are just so large.

Next, paint, paint, paint! Paint an entire sheet of newspaper, just one side though. Don’t worry if some of the newspaper can be seen through the paint, nobody will notice when the hat is finished! Allow the paint to dry completely.

After the paint is dry, lay the paper overtop of another sheet of newspaper…two sheets will make the hat a little more durable. Fold the papers twice, once in each direction, and cut the paper so when you open them back up, you have a circle. The circle really doesn’t have to be perfect, it’ll look great when you’re done!

Next is the tricky part because kids tend to wiggle…lay the paper over your child’s head and scrunch fold it into shape. As you go around, use painters tape to hold the the folds in place. The great thing about painter’s tape is that you can fix any little mistakes and it won’t tear up the paint or paper.

In making WB’s orange hat, I just shaped it around my knee and it worked just fine. I also experimented and used a stapler instead of the painters tape. Stapling worked great and looks fantastic, but it is a little trickier to do. The paper tears a little easier with staples in it too.

Now to decorate your hat! You can cut flowers out of tissue paper or just cut squares and scrunch them up. If you layer the tissue paper a bit, the flowers are a little fluffier and prettier. You can also glue on poof balls, jewels, feathers, anything you can think of and find around your house!

Super cute, huh!? Forget Easter bonnets, we’ll be wearing these to Thanksgiving dinner!!! That is if they survive a month’s worth of tea parties…

Wouldn’t these be adorable for a birthday party? You could make the hats beforehand and let the kids decorate them at the party…so many fun possibilities! Enjoy!